632 "Patriot" Complete Kit


632 "Patriot" Quality Race Engine Kit/Build

Another performance kit/build by Ray @ Raymac Racing Engines


632 “The Patriot” Race Kit - Get a Big’ol Bang for your buck using your TAX REFUND! The best way to spend your tax dollars ;)

Short Block Kit $5,590
World 4.600 x 10.2 Deck Merlin IV
Dart 4.750 Center Counterweighted 4340 Crankshaft, Internally Balanced
Manley 6.700 4340 H Beam Rod with ARP 2000 Bolts
JE 4.600 Bore 1.120, 36cc Dome 2618 Forged Piston 14.4:1 Compression with 118cc Head
JE Pro Series Ring Set 1/16, 1/16, 3/16 Plasma Moly
Clevite H Series Rod and Main Bearings

Top End Kit $3,975
Dart Pro1, 345cc, 121cc Chamber Aluminum Heads, 400 cfm, 2.300/1.880
ARP 8740 Head Studs
JE MLS Head Gaskets
Crane “Gold” 1.7 Ratio Aluminum Rockers
Raymac Racing Engines Stud Girdle
Polished Cast Aluminum Tall Valve Covers

Valvetrain Kit $1,480
Custom 8620 Steel Mechanical Roller Cam
Comp Cams High Pressure Oiled Mechanical Lifters
Tru Roller, Steel Billet Geared, Roller Thrust Timing Chain, Lockplate, Button
Chrome GM Timing Cover
Trend Pushrods 8.600” Int 9.300” Exhaust ⅜ x.080 wall

Oil System, Carburetor & Intake, Balancer & Accessories $3,375
Moroso 7q Comp Eliminator Aluminum Oil Pan
Moroso High Volume Oil Pump & H/D Welded Pickup & Drive
MSD Distributor & Wires with Bronze Gear
Cast Aluminum Single Plane Intake Manifold
Quick Fuel 1150cfm Carburetor
ATI Internal Balanced Balancer
Pan Gaskets, Intake Gaskets, Valve Cover Gaskets, Rear Main Seal, Plugs, Oil, Oil Filter Adaptor, Hardware, Dist. Hold Down, Balancer Bolt

Total Parts $14,420 (unassembled kit)

If Labor in needed add $2310
Hone Cylinders with Torque Plate & Valley Lugs
Deck Block
Pin Fit Pistons & Rods
Polish Crankshaft
Disassemble Heads, Clean, Lap Valves, Set Heights, Reassemble
Final Wash All Parts
Assemble Complete Engine -
Individually Fit Bearings (Rod & Main), File Fit Rings, Degree Cam, Set Compression & Piston to Valve Clearance, Check/Set Stroker Clearance, Professionally Assemble Complete Engine
Dyno Test & Tune

Total Parts & Labor $16,730 (assembled)
Bill Mitchell Products Aluminum Block +$2,100
Hellfire Ring Set (N2O) +$175
GRP Aluminum Rods +$750 (Installed will increase stroker clearance labor by +$200)
Callies Magnum Crankshaft +$1100
Jesel Beltdrive +$800
Holley and Profiler Intakes Available (Call for details)
Brodix Headhunter Heads (Call for details)


Contact Raymac Racing Engines

       This email address is being protected from spambots. You need JavaScript enabled to view it.  

Call us for a free quote!

817.705.5424   or  940.594.0350

All products are subject to availability. Customizing a part may delay shipping. All prices are subject to change.

09/05/18 California law now requires any reseller of California based manufactured parts (including by not limited to Dart, Race Winning Brands, AFR, Scat and Brodix) to inform it's customers of the following (in accordance with Proposition 65): WARNING: May Cause Cancer and Reproductive Harm - www.P65Warnings.ca.gov. The notice also states these California based part manufacturers will be placing warning labels on those products effected (affixed to products, labels or packaging).